New Parts Topic

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
24 Apr 2019 13:46 #15342 by Geno
Replied by Geno on topic New Parts Topic

Geno wrote: I haven't been in here for awhile, There is too much stuff for 1 man to do around here, I think I may need some help... :tounge2

Every now and then I go on a parts hunt, I've been looking for these on and off for many years and finally found what I think is as close as I can get. They are the wire clips. These are made to hold more wire and they don't make a smaller one. On the bright side they are almost the same as far as measurements, the part that digs into the steel and leaves ugly on the paint is on the inside instead of the outside, and they are stainless. They do need to be closed up a little to hold the smaller wires though, I did one in the 1st pic, just a little squeeze with a pair of pliers. :thumb1


Just took a min to get them in the store. :thumb1

Welcome to the Stables!

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
18 May 2019 18:47 #15466 by Geno
Replied by Geno on topic New Parts Topic
With the Clydesdale moving along so quick (thanks to Clint) and someone wanting to come pick up a rockshaft today, let alone all of the calls I've been getting on it lately since I've mentioned how cheap it is, I thought I could spare some time to finish it. We finished the jig today and put a locator pin in it so I couldn't weld them backwards. :laughing I am going to build 10 of them and have them done next week. I forgot how nice it is and how much more gets done with 2 extra hands around. :woo

Clint got all of the parts blasted up today and they are ready to weld together and paint. :thumb1

Welcome to the Stables!
Attachments:

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
20 May 2019 19:51 #15470 by Geno
Replied by Geno on topic New Parts Topic
Got 10 of them welded up for Clint to clean up + blast tomorrow. :thumb1

Welcome to the Stables!
Attachments:

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
30 May 2019 10:58 - 30 May 2019 11:00 #15492 by Geno
Replied by Geno on topic New Parts Topic
The rock shafts will be ready in time for the show next weekend. :thumb1

Welcome to the Stables!
Attachments:
Last edit: 30 May 2019 11:00 by Geno.

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
31 May 2019 11:04 #15493 by Geno
Replied by Geno on topic New Parts Topic
Actually they are ready now. :thumb1 They will be available at the show and I will be getting them in the store after the show, rock shaft, oil impregnated bushings and clips will be in this kit, every piece Made in USA for $59.99. :yes

Welcome to the Stables!
Attachments:

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
14 Jun 2019 10:01 - 14 Jun 2019 10:03 #15520 by Geno
Replied by Geno on topic New Parts Topic
Added the Wheel Horse 108537 / 253-44 Seal used on the 520-H brake shaft and many other models to the store yesterday. It's about 1/2 the price of most other places and NOT made in China lol. Also added the 1" exhaust locking nuts Made in USA. :thumb1

253-44 Seal

Exhaust Locking Collar

I have the only front wheel bearing kits and grease caps in stock already NOT made in China that I think exist for the 520 as well, even the Toro parts are made in China. :doh I'm working on getting the rock shafts in there now, had another call on them this morning...

Welcome to the Stables!
Attachments:
Last edit: 14 Jun 2019 10:03 by Geno.

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
03 Oct 2019 14:20 - 03 Oct 2019 14:24 #15591 by Geno
Replied by Geno on topic New Parts Topic
Got the 520H front bearing sets in the store today. The bearing + race set is cheaper than just the bearings from everyone else (not including China junk), these are all Made in USA. :thumb1


520H front bearing set

Welcome to the Stables!
Attachments:
Last edit: 03 Oct 2019 14:24 by Geno.

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
08 Nov 2019 18:04 #15633 by Geno
Replied by Geno on topic New Parts Topic
I found a shipping option yesterday for the dash plates that wouldn't fit in the flat rate box for about the same price so I got back to this long overdue project... There are also some other bigger things that can go in the store now without having to mess with the flat rate shipping. :smile2

Started on the guide for the bend last night and finished it up today. It's within .001" from end to end so I stopped there before I went too far and had to start over. :laughing The same guide and bend setting works on all of the metal plates. I have 100 of the older styles to bend now and had to come up with a way to get them done quickly and accurately.

Welcome to the Stables!

Please Log in to join the conversation.

  • Geno
  • Topic Author
  • Online
  • Administrator Supporter
  • Administrator Supporter
    Super Users
  • Wheel Horse Stables Owner
More
11 Nov 2019 10:38 #15640 by Geno
Replied by Geno on topic New Parts Topic
Justin brought something to my attention last weekend. I thought the lift height adjustment knobs were in the store but they weren't. :doh But they are now. :yes

Thanks Justin. :thanks

They are here - Lift Height Knob

Welcome to the Stables!
Attachments:

Please Log in to join the conversation.

More
13 Nov 2019 19:37 #15641 by JustinW.73
Replied by JustinW.73 on topic New Parts Topic
Just doing my job! :smile2 :hemademe :hemademe1

1973 No Name 16
1966 856
1964 854
198? 520H
Way too many decks
1966 f100
The following user(s) said Thank You: Geno

Please Log in to join the conversation.

Time to create page: 0.591 seconds